Plastic magnetic drive pumps

pompe-magnetiche-plastica

  • Leak-proof design without mechanical seal.
  • For clean corrosive liquids without solids.
  • Close-coupled pump with space saving design.
  • Materials: PP, PVDF.
  • Flow-rate up to 135 m³/h and heads up to 48 m w.c.


Plastic magnetic drive pumps

Q max m³/h H max m w.c. kW ATEX version Material
BM04 3.5 7 0.12 Atex zone 2 PP – PVDF
BM06 6,5 8 0.25 Atex zone 2 PP – PVDF
BM10 13 12 0.55 Atex zone 2 PP – PVDF
BM15 23 19 1.1  – 1.5 Atex zone 2 PP – PVDF
BM31 30 24 2.2 – 3 Atex zone 2 PP – PVDF
BM40 42 30 3 – 4 Atex zone 2 PP – PVDF
BM50 42 33 5.5 – 7.5 Atex zone 2 PP – PVDF
BM80 92 39 7.5 → 22 Upon request PP – PVDF
BM100 135 48 7.5 → 22 Upon request PP – PVDF

Mag-drive centrifugal pumps made of plastic, created by injection molding up to BM50 size. Whereas, starting from the BM80 model, they are mechanically machined from solid plastic block.

BM magnetic pumps operate with maximum nominal pressure PN 4 to 20°C.

index BM series mag-drive pumps – catalogue
index Mag-drive pumps performance curve

Performance curves

The range of BM magnetically coupled pumps guarantees flow-rates from 135 m³/h and heads up to 48 m w.c.
(meters water column). The performance can change as the characteristics of the liquid being pumped vary.
Pumps with 60 Hz motors are available upon request.


userblock32 Series BM4-BM6-BM10-BM15-BM31 performance curves – download here
userblock32 Series BM40-BM50-BM80 performance curves – download here
userblock32 Series BM100 performance curves – download here

Corrosion resistant materials

The structural and hydraulic plastic parts of BM magnetic pumps are made of PP or PVDF (injection molded, drawn, extruded or plastic sleeved). The plastic material is chosen according to the specific operating conditions: corrosion resistant plastic resins with different chemical compatibilities based on the liquids to be pumped.

Material of pumping unit:

  • Pump and impeller: PP or PVDF.
  • Static shaft: Sintered Ceramic (Al2O3).
  • Bushing: filled PTFE (option: Silicon Carbide).
  • O-ring: EPDM (pumps made of PP) or FPM (pumps made of PVDF).

Magnetic coupling materials:

  • Permanent magnets made from neodynium-iron-boron (NeFeBo).

Mag-drive pump options

Savino Barbera magnetically coupled pumps can be assembled with some optional equipment:

  • 4 pole motors with 60 Hz power (1450 rpm).
  • Explosion proof motors (Ex-d).
  • Base-plate made of PP in three different sizes.
  • Zone 2 ATEX pumps.
  • Connections: backing rings, hose adaptors, male threads (depending upon the models).

pompe-magnetiche-con-basamento

index Technical sheet for base plates – download here

Mag-drive pumps videos

Some images illustrating the variety of our magnetic pumps BM series:

Magnetic drive pump with flame-proof motor and backing rings connections.

Magnetically driven pump made
of PVDF for hydrochloric acid.

Mag-drive pumps for HCL,
with kW 2.2 motors.

Mag-drive pumps videos

Videos illustrating the technical characteristics of our magnetic drive pumps:

Mechanical seal or magnetic coupling?

The choice between mechanical seal pumps and magnetic drive pumps can easily be misled by incorrect
installation habits. For example, we are sometimes asked to provide mag-drive pumps for services not
compatible with applications requiring zero emissions: those who prefer the magnetic coupling can in
fact presume that the transmission through magnetic joint is a safer system compared to the mechanical
seal. However, if on one hand the mechanical seal is more easily subject to leakage, on the other hand
the supposed hermetically closed design of encapsulated magnets must be taken into consideration because
it can become a problem for the nature of some liquids. To make a calculated technical choice, we invite
you to read this section:


icona-tenute-meccaniche Pros and cons of sealed pumps and magnetic pumps

Sealless magnetic drive pump BM model

Horizontal mag-drive pump (BM Series).

Mechanical seal pump OMA model

Horizontal mechanical seal pump (OMA Series).


Savino Barbera srl

Via Torino 12
10032 Brandizzo, ITALY
P.IVA 00520820010
R.I.TO 272-1974-2166
REA 489443
Cap. soc. 48000€ i.v.

Tel +39 011 913.90.63
info@savinobarbera.com

New on Instagram

  • Relic day how we tested our pumps in the beginninghellip
  • New catalogue coming soon pumps savinobarbera
  • Savino Barbera will celebrate 70 year in 2017

Be social:

  • twittertwitter
  • facebookfacebook
  • g plus profileg+
  • Pinterest profilepinterest board
  • youtubeyoutube
  • linkedin profilelinkedin